High Quality Baler For Compacting Materials

• After-sales Service: Instruction for Commissioning and Maintenance
• Warranty: 12months
• Condition: New
• Certification: GMA, QS, ISO, CE
• Automation: Automatic
• Screw: Multi-Screw
• Model NO.: S-120KV
• Treatment: Compaction
• colour: red,white
• Transport Package: Polywood
• Trademark: JONO
• Origin: China
• HS Code: 84798999

Product Description

  

Product Description

The JONO baler is a fully automatic system for compacting different types of materials and their processing into bales. The handled materials are first compacted and subsequently tied into bales.
 

Working Principle

 

After the material has reached the desired fill level on the filling chamber, the cover of the baler is closed automatically. When the baler cover is closed, the main ram presses the materials together. At the same time the baler is refilled from the feed belt. After the ram has reached the foremost position, it moves back again. The material that has been pressed enough is loaded into the intermediate hopper above; the cover of the baler will then open again and refill the cover of the baler with the material. The cover of the baler closes again after the material has fallen into the compression chamber of the baler.
This procedure is detected by photocells. The whole process is repeated until the desired bale length (which is adjustable) has been reached. The cover stops in front position after the cycle mentioned above is finished. The wire device moves through the cover around the bale, from the bottom up. The device accepts a wire from below and from above the baler. After the wire device is again in the top position, the wires are cut and connected. After that, the press ram moves backward again and the whole process is repeated.
 

Technical Data

Model	S-120KV
Length (mm)	9948
Width(mm)	2390
Height(mm)	3035
Pressing force Pre-compressing flap(t)	2x20
Drive power (kW)	90
Max.Press power(bar)	290
Main hydraulic cylinder-working length(mm)	2600
Spec.Press force  (kg/cm²)	15,1
Pressing force (T or kN)	120/1200
Volume/cycles(m3)	2,9
Cycle without Material without twisting (sec)	20
Cycle twisting(Sec)	14
Performance 30 kg/m3(t/h)	13-16
Performance 50 kg/m3(t/h)	20-25
Performance 100 kg/m3(t/h)	28-32

Through capacity can vary depending on the material.

 

Features

The cover of the bailing press ensures that a closed press channel is built, so that a difficult compressible material does not need to be cut off during the pressing process.
Thanks to the cover of the bailing press, much more material is compressed per cycle. The capacity of a baler is also much larger than the capacity of balers with cutting system with a comparable engine performance.
Since the baler is not equipped with a cutting knife, the maintenance costs are much lower, because regular exchange of cutting blades is unnecessary and the guide strip and wheels can be used by the low load longer.
The material is equally distributed in the bale and the bales are more compact and rectangular. Therefore, such bales are much easier to stack than bales from a cutting press.
The fill opening is as wide and deep as the press chamber.

 

Main Products

 

 

 

Sucessful Projects

     By 2018, JONO has undertaken more than 80+ EPC Projects, which are distributed in more than 40 cities . Our equipment is capable of handling more than 50,000 tons of waste every day.Through persistence and accumulation, we have the proprietary knowledge of total solutions in eight segments, including Municipal Solid Waste (MSW), organic waste, decoration waste, construction waste, recyclables, bulky waste, industrial waste and landfill waste.
 

                                         LOCATION                                             SINGAPORE

APPLICATIONMUNICIPAL SOLID WASTE

CAPACITY      600T/D

This project with the treatment capacity of 600t/d is set for a fine sorting of MSW before they were sent to the CFB (circulating fluidized bed) for incineration. Specifically, JONO introduces the Lindner shredding technology and adopts two-stage shredding process in this project to shred the combustible materials into 80 mm fuel (SRF) so as to enhance the complete combustion rate and mitigate the pressure of treating the exhaust gas. Besides, the mechanical sorting process is also applied in this project to sort out ferromagnetic metals, in-combustibles (glass, stone, ash, etc.) and combustibles.

The first pilot plant at Singapore to treat the non-source sorted waste, it includes pre-treatment, bio-drying and post-treatment, within the pre-treatment, HDPE, LDPE,PP and MIX PET will be sorted out, the remains will be sent to bio-drying box, after 8-9days, the water content will be reduced from 45% to 25%. After the post treatment,ferrous, non-ferrous and inert could be separated. Eventually the calorific value of RDF will be increased from 1000kcal/kg to 3800kcal/kg, which could reach the EU standard Class III. This MBT plant is focusing on recycling and RDF production, a good reference case for the idea of " waste to value".

                                              


                                            

                    LOCATION                                                            APPLICATION                                   CAPACITY                           VIETNAM                                                    MUNICIPAL SOLID WASTE                       1,000T/D               

Mixed MSW is a general term for recyclable waste, organic waste, hazardous waste, combustible waste, etc.

 

Jono has independently developed the MSW mechanical biological treatment (MBT) technology, and launched the automatic disposal scheme of waste classification and treatment smart factory.   After the intelligent separation of mixed MSW, the disposal path for products includes: Aerobic/Anaerobic fermentation to produce high-quality biological fertilizer; plastic granulation; production of high calorific value refused derived fuel RDF.

About us

JONO was founded in 2006 and is located in Wujiang District, Suzhou. The company has a floor area of 25,000 square meters, more than 80 design researchers, more than 200 employees and more than 150 patents. It is a new landmark of Wujiang enterprise, also a national high-tech enterprise, has been rated as a waste sorting leader for four consecutive years by the industry association.


For more infomation,pls click on the following link:

FAQ

1. Question: Will JONO provide pre-sale services?
    Answer: JONO has an experienced team of experts, and we will provide the right solutions in a timely manner according to the needs of our customers.
2. Question: Can I visit JONO's factory at any time?
    Answer: If you are interested in our products and would like to visit our factory, then please contact us and and we will help you make it happen.
3. Is JONO's after-sale service excellent?
   Answer: We have a professional technical team that can assist with on-site installation, commissioning, training and operation. The technician will also introduce the customer to all aspects related to operation and maintenance. If necessary, we will also have a professional after-sales team to go to the scene in time to solve all problems related to products for customers.